Mitutoyo 500-177-20 ABSOLUTE Digimatic Caliper with SPC output

Measuring Range 0-8"/0-200mm
Resolution .0005in 0.01mm
Accuracy ±.001in
with OD, ID carbide jaw

Availability: In stock

$411.00
OR
 

Mitutoyo 500-177-20 ABSOLUTE Digimatic Caliper with SPC output

Double click on above image to view full picture

Zoom Out
Zoom In

More Views

  • Mitutoyo 500-177-20 ABSOLUTE Digimatic Caliper with SPC output

Product Description

FEATURES:

Large and clear LCD readout.
The ZERO/ABS key allows the display to be Zero-Set at any slider position along the scale for incremental comparison measurements. This switch will also allow return to the absolute (ABS) coordinate and display of the true position from the origin point (usually jaws-closed point).
Carbide-tipped jaw type calipers are also available.
With thumb roller. Except 500-500-10, 500-501-10,500-502-10.
Supplied in fitted plastic case. Except 1000mm / 40” supplied in wooden case.

Technical Data
Accuracy: Refer to the list of specifications
Resolution: 0.01mm or .0005"/0.01mm
Repeatability: 0.01mm / .0005”
Display: LCD
Length standard: ABSOLUTE electrostatic capacitance type
linear encoder
Max. response speed: Unlimited
Battery: SR44 (1 pc.), 938882
Battery life: Approx. 3.5 years under normal use

Function
Origin-set, Zero-setting, Data output, inch/mm conversion
(inch/mm models ONLY)
Alarm: Low voltage, Counting value composition error

Optional Accessories
959143: Data hold unit
959149: SPC cable with data switch (1m / 40”)
959150: SPC cable with data switch (2m / 80”)

*without SPC data output

The Mitutoyo ABSOLUTE 500 series caliper is a Digimatic digital caliper that is made of durable hardened stainless steel and uses Mitutoyo’s ABSOLUTE linear encoder technology, which allows you to “set and forget” the origin and measure in awkward or difficult locations.

This digital caliper has LCD readout and function control buttons on the caliper face, including Origin to set and retain the original measuring point, and Zero/ABS (Absolute Scale) to zero-set the LCD display. It uses the metric measuring system.

Although identical to dial and vernier calipers in its ability to make precise measurements, the digital caliper also has an LCD, which clearly shows values and increases reading reliability over the other types, and reflects all ABSOLUTE system activities. The Absolute Scale (ABS) function tracks the origin point you set, even after shutoff. Once on again, the caliper can immediately start measuring, without zero resetting or concern of overspeed errors. The LCD can be "zeroed out" before making and comparing incremental measurements without having to subtract the first measurement from the second.

The calipers use the ABSOLUTE electrostatic capacitance linear encoder which helps prevent overspeed errors. They measure outer diameter (OD), inner diameter (ID), depth, and step, where the butt end of the fixed jaw measures one end of a work piece before its upper/lower or inner/outer "steps" are measured. LCD Resolution is 0.01mm. Also included are origin-setting, zero-setting, and on/off automatic shutoff function buttons. A Digital LCD Data Reading Hold function is available with the optional Data Hold Unit (sold separately). An alarm alerts the user to low voltage and scale contamination and counting value composition errors. A rolling thumb wheel makes fine adjustments and a thumb screw locks the scale’s position. Response speed is unlimited. Each caliper includes, and is powered by, one SR44 silver oxide cell battery that lasts approximately 3.5 years with continuous normal use.

Calipers measure the distance between two opposing sides of an object. They make inside, outside, depth, or step measurements, according to their type. Calipers are commonly used in architecture, metalworking, mechanical engineering, and machining. The simplest calipers have two legs to mark the two points and require a ruler to take the measurement. More complex calipers use two sets of jaws instead of legs and have up to two graduated scales. Vernier, dial, and digital calipers give direct and accurate readings and are functionally identical, having a calibrated scale with a fixed jaw, and another jaw with a movable pointer that slides along the scale. The vernier caliper has a scale sliding parallel to the main scale for an additional, fractional reading to improve measurement precision. The dial caliper has a circular dial with a pointer on a toothed gear rack replacing the second vernier scale. As with the vernier, this second measurement is added to the reading from the main scale to obtain the result. The digital caliper takes a differential by zeroing the display at any point along the slide, with an LCD that displays a single value in English and/or metric units.

We Also Recommend

You may also be interested in the following product(s)

C-959150-06 Mitutoyo Gage Cable

C-959150-06 Mitutoyo Gage Cable

Regular Price: $55.20

Web Only Price: $52.45

Data send switch - Clamshell Style, 6' cordset, C-FS25-06, 2.5mm male plug

Data send switch - Clamshell Style, 6' cordset, C-FS25-06, 2.5mm male plug

$45.00
Mitutoyo 500 Series ABSOLUTE Digimatic Calipers

Mitutoyo 500 Series ABSOLUTE Digimatic Calipers

From: $136.80

To: $1,705.45

   

Additional Information

SKU 500-177-30
UPC 603908420927
EAN 4946368526416
Weight (in lbs) 1.2
Manufacturer Mitutoyo
Gage Type Caliper
Gage Cable 959150
Measuring range 0-8"/0-200mm
Resolution .0005in/0.01mm
Accuracy ±.001in
Remarks with OD, ID carbide jaw